Mivan grease and batata (yellow) grease both go on aluminium formwork hardware, never on the panel face. Batata grease is the low-cost general site grease. Mivan grease is the trade name for grease sold for pins, wedges and ties. Neither is a fixed standard, so choose by your hardware and crew, and trial a sample.
On most aluminium formwork sites in Mumbai and Thane, someone eventually asks: do we really need Mivan grease, or will the batata grease already in the store do? It is a fair question. Both are greases, both go on the same pins and wedges, and the price difference is visible on every order. This guide compares them honestly, explains why there is no one-line answer, and gives you a way to decide on your own site. For the dedicated product, see our Mivan shuttering grease page.
Mivan grease vs batata grease at a glance
| Point | Batata (yellow) grease | Mivan grease |
|---|---|---|
| What the name means | Local trade name for yellow calcium soap grease | Trade name for grease sold for aluminium formwork hardware |
| Is there a standard? | No. Varies by maker | No. Varies by maker |
| Where it goes on Mivan | Pins, wedges, tie rod threads, props | Pins, wedges, tie rod threads, kicker bolts, props |
| Panel face | No | No. The face takes Mivan shuttering oil |
| Other site uses | Conventional shuttering, clamps, trolley wheels | Mainly formwork hardware |
| KE rate | Rs 65 per kg, delivery and GST extra | Quoted with the enquiry |
| KE consistency | Made to the requirement | Made to the requirement |
The name on the pail tells you less than you think. Two “Mivan greases” from different makers can differ more from each other than one of them differs from a good batata grease. What matters is how the grease behaves on your pins in your weather.
What is the same
- The job. Both keep slurry from setting on hardware, let pins drive out and wedges release, and slow rust on steel parts.
- The rule for the panel face. Neither belongs on the aluminium face that touches concrete. That surface takes a thin release coat of Mivan shuttering oil.
- The routine. Clean after stripping, dry, brush on a thin film, store covered. A good routine with an ordinary grease beats a poor routine with an expensive one.
What can differ
Consistency
Some formwork greases are firmer, some softer and more slippery. A firmer grease stays on hardware lying in the sun; a softer one brushes more easily into wedge slots. At KE both yellow grease and Mivan grease are made to the requirement, so the consistency follows the job rather than the label.
How it behaves near the panel
Pins and wedges sit right next to the panel face. A grease that runs or smears easily ends up on the face and then on the concrete. Watch for this during a trial, whichever grease you test.
Heat and water
As a general statement about conventional calcium grease (not a KE specification), it resists water well but softens as it warms. Exposed hardware in summer sun can get hot enough to soften a soft grease. In the monsoon, curing water and rain wash weak grease off within a cycle.
Price
Batata grease is usually the cheaper line. But grease cost on a tower is small next to the labour lost to one jammed floor. Judge by grams used per point and stripping time, not by rupees per kg alone.
When each one makes sense
Batata grease fits when
The site also runs conventional shuttering and wants one grease in the store; hardware is cleaned and re-greased every cycle; crews brush a thin film; and a trial shows it stays on through curing.
Mivan grease fits when
Pins jam or rust between floors with the current grease; hardware lies in sun or rain for days; grease is reaching the panel face; or the formwork supplier asks for a dedicated hardware grease.
Whatever you choose, check your formwork manual first. Systems differ, and at least one manufacturer instructs that its assembly locks must never be oiled or waxed. Where the manual names a part to keep dry, follow the manual.
How to decide on your own site
- Mark two sets. On one floor, mark about 50 pin and wedge sets with paint. Grease half with each product.
- Weigh the tins. Weigh each tin before and after the shift to get grams per point.
- Strip and compare. At stripping, note which pins came out by hand or with a light tap, and which needed a hammer.
- Check the face. Look for grease marks on the panel face and the concrete near the joints.
- Repeat once. Run a second cycle, ideally after rain or a hot day, before deciding.
The full trial method, with a scorecard, is in how to trial a Mivan grease sample. To size the order afterwards, use Mivan grease consumption. The step-by-step routine is in how to grease Mivan formwork.
Switching greases without cleaning the pins. Different greases can be incompatible when mixed. Clean the old grease off before a trial, or the result tells you nothing.
Ask for both samples
KE makes both yellow grease and Mivan grease, as different grades chosen per requirement. Tell us your hardware, how the crew applies grease and where the site is, and ask for a sample of each to run side by side. Yellow grease is Rs 65 per kg, plus delivery and GST. Mivan grease is quoted with the enquiry. Any quantity can be supplied. More on the shuttering side is in batata grease for shuttering and the yellow grease (batata grease) page.
Krish Enterprises, K.J. Complex, Diva, Thane 400612. Call or WhatsApp +91 96194 84337.
Frequently asked questions
Is Mivan grease the same as batata grease?
No. Both are used on aluminium formwork hardware, but they are different products and neither name is a fixed standard. At KE they are different grades, chosen per requirement.
Can I use batata grease on Mivan pins and wedges?
Many sites do. Clean the pins first, brush on a thin film and keep it off the panel face. Trial it against a Mivan grease on a few sets before you decide.
Which is better for Mivan shuttering, batata grease or Mivan grease?
It depends on your hardware, weather and how the crew applies it. A side-by-side trial on one floor answers it better than any label.
Can either grease go on the Mivan panel face?
No. The panel face takes a thin coat of Mivan shuttering oil as a release agent.
What is the price difference?
KE yellow grease is Rs 65 per kg plus delivery and GST. Mivan grease is quoted with the enquiry, based on the requirement and quantity.
What is shuttering grease?
On Indian sites it usually means batata grease used on formwork hardware. Grease sold specifically for aluminium formwork is often called Mivan grease.

