Batata grease is widely used on Indian sites for shuttering hardware: tie rods, wing nuts, clamps, pins and wedges. It is cheap and resists water. For panel and plywood faces, a shuttering oil or Mivan release oil is usually the better choice, because grease leaves a thicker film that can mark concrete and affect plaster bonding.
Ask a shuttering foreman what he puts on tie rods and the answer is often “batata grease”. It is a very common site grease. But the same tin also ends up on panel faces, plywood edges and Mivan pins, and that is where questions start. This guide sets out which shuttering jobs batata grease suits, which ones need an oil, and how it compares with a dedicated Mivan grease. For the product and rates, see our yellow grease (batata grease) page.
How sites use batata grease on shuttering
Batata grease shows up on shuttering in two quite different ways:
- As a lubricant on hardware. Tie rods, wing nuts, props, clamps, scaffolding couplers, pins and wedges. This is what grease is made for.
- As a release coat on the form face. Some crews smear it on plywood or panel faces, usually in tight corners where stripping is hard. This is where problems come from.
Site engineers who have used grease as a release coat report the same issues: crews over-apply it, the concrete surface stays greasy long after stripping, and plaster or paint may not bond well where grease has been. Release oils are designed to leave a much thinner film.
Which product for which shuttering job
| Job | Batata grease | Shuttering oil (plywood) | Mivan oil (aluminium release) | Mivan grease |
|---|---|---|---|---|
| Tie rod and wing nut threads | Good | Poor, runs off | Not designed for it | Suits hardware |
| Props and prop threads | Good | Poor | Not designed for it | Suits hardware |
| Scaffolding couplers, trolley wheels | Good | Poor | No | Not the usual choice |
| Mivan pins and wedges | Used on many sites | Poor | No | Sold for this hardware |
| Plywood shuttering face | Not recommended | Made for it | Possible | No |
| Aluminium panel face | Not recommended | Not ideal on metal | Made for it | No |
| Fair-faced or exposed concrete | Avoid | Use a suitable oil | Use a suitable oil | No |
The short rule: grease for moving and threaded hardware, oil for faces that touch concrete.
Where batata grease works well
Batata grease, as commonly sold, is a calcium soap grease. Conventional calcium grease resists water washout well and is low in cost, which is why it suits shuttering hardware:
- Tie rods and wing nuts. A thin coat on the thread keeps slurry out and lets the nut spin off after the pour.
- Props. Grease on the screw thread keeps height adjustment smooth through the monsoon.
- Clamps, channels and clips on conventional plywood shuttering.
- Scaffolding couplers, trolley wheels and barrow axles.
- Gate hinges and rollers on site hoardings.
These parts get wet, move slowly and stay cool. That is exactly the duty calcium grease is good at.
Where shuttering oil is the better choice
On the form face, an oil beats grease for three reasons:
- Thinner film. A release oil can be sprayed or wiped as a thin, even film. Grease goes on thick and patchy.
- More area per kg or litre. Our Mivan shuttering oil consumption guide shows fine-spray coverage of about 30 to 40 m² per litre. Hand-spread grease covers far less.
- Cleaner concrete. Less residue means less cleaning before plaster or paint.
If a crew must use grease as a release in one awkward spot, keep the coat as thin as possible, wipe off the excess, and never use it on surfaces that will be left exposed or painted directly.
Know the heat limit
As a general statement about conventional calcium grease (not a KE specification), the drop point is usually around 90 to 100°C and the grease starts to soften well below that. As a working rule, keep it on parts that stay below about 60 to 70°C. Hardware lying in direct summer sun gets hot, and a soft grease can run off. Store tins in shade and re-grease hardware that has sat in the sun.
KE does not sell one fixed grade. We make the grease to your project and requirement, some thicker and some more slippery. If your parts run hot or sit in the sun, tell us the application and ask for a sample before ordering.
Batata grease or Mivan grease on aluminium formwork?
Many Mivan sites use batata grease on pins and wedges because it is cheap and easy to get. It does the basic job of keeping slurry off and parts moving.
KE’s yellow grease and Mivan grease are different grades. Some are thicker and some more slippery, and each is chosen per requirement, so there is no single rule for which to use. Tell us what you are greasing and how, and ask for a sample of either before you order. No Mivan grease rate is quoted on this page.
Whichever grease you use, the routine matters more than the brand: clean after stripping, apply a thin film, keep grease off the panel face. The full routine is in how to grease Mivan formwork. For the dedicated product, see Mivan shuttering grease.
Buying batata grease for shuttering work
- Order size. Any quantity can be supplied and there is no minimum order. Shuttering gangs often do well with 1 kg tins, refilled from an 18 kg pail in the store. Open pails on the deck collect dust.
- Price. KE quotes yellow grease at Rs 65 per kg, plus delivery and GST. The breakdown, with GST worked out for a pail, drum and barrel, is in our batata grease price guide.
- Quality. Good batata grease is smooth, not grainy, and does not sit under a thick layer of oil. A quick check some engineers use: a small lump dropped in water should float. Grease that sinks fast may be bulked with dense fillers.
- Do not mix greases. Calcium and lithium greases can be incompatible. If you switch a part from AP3 or MP3 to batata grease, clean off the old grease first. More on this in yellow grease vs lithium grease.
Need batata grease in bulk?
Tell us the quantity, what you will grease and the site location, and ask for a sample of our yellow grease (batata grease) before you order. We will reply with the rate, GST and delivery cost. Rates for larger quantities and delivery cost are quoted with the enquiry.
- Call: +91 96194 84337 or +91 98335 42232
Krish Enterprises, K.J. Complex, Diva, Thane 400612. Serving Mumbai, Thane, Navi Mumbai and Panvel.
Frequently asked questions
Can batata grease be used for shuttering?
Yes, on shuttering hardware such as tie rods, wing nuts, props, clamps, pins and wedges. For the faces that touch concrete, a shuttering oil or Mivan release oil is the better choice.
Is batata grease a good release agent for formwork?
Not usually. It leaves a thick film that is hard to apply evenly, can mark the concrete and may affect plaster or paint bonding.
Can I use batata grease on Mivan pins and wedges?
Many sites do. A dedicated Mivan grease is sold for this hardware. Either way, clean the pins first and keep grease off the panel face.
Why does batata grease run off hardware in summer?
Conventional calcium grease softens as it heats up. Hardware in direct sun can get hot enough for the grease to thin and drip.
What is shuttering grease?
On Indian sites, shuttering grease usually means batata (yellow calcium) grease used on formwork hardware. Some suppliers also sell grades made for aluminium formwork, often called Mivan grease.
