Mivan shuttering oil is a thin release agent sprayed on the aluminium panel face so concrete does not stick. Mivan grease is a thicker lubricant brushed on pins, wedges, tie rod threads and prop threads so the hardware keeps moving. Oil goes on the face, grease goes on the hardware. Budget them separately.
Every aluminium formwork site buys both, and someone always asks whether one can replace the other. It cannot. This guide sets out what each product does, where it goes, what goes wrong when they are swapped, and how a site plans the quantity of each. The products are our Mivan shuttering oil and Mivan shuttering grease.
Use oil on every surface that touches concrete. Use grease on every steel part that has to slide, lock or turn. A site that buys only one of them ends up with either rough concrete or jammed hardware.
Mivan oil vs Mivan grease at a glance
| Point | Mivan shuttering oil | Mivan grease |
|---|---|---|
| Main job | Release agent: stops concrete bonding to the panel | Lubricant: lets hardware move, keeps slurry off, slows rust |
| Where it goes | Panel contact face, deck sheets, beam sides | Pins, wedges, tie rod and wall tie threads, kicker bolts, prop threads, panel joint edges |
| Form | Thin liquid | Soft paste |
| How it is applied | Fine spray (or cloth wipe) on clean, dry panels | Brush or gloved hand, one thin film |
| How often | Before every pour | Pins and wedges every cycle, other parts every few cycles or weekly |
| Sign it was skipped | Concrete sticks, rough or patchy surface, slow stripping | Pins that will not drive out, jammed wedges, threads that need a hammer |
| Planned by | Litres, from panel face area | Kilograms, from the number of points greased |
Where Mivan shuttering oil goes
Shuttering oil goes on every face that will touch wet concrete: wall panels, deck panels, beam sides and kickers. Its only job is release. A thin, even film stops the cement paste bonding to the aluminium, so the panel comes away cleanly and the wall needs less finishing.
Formwork makers ask for a very thin coat on a dry, clean face. Aluminium panels need a release agent made for metal formwork, not a plywood oil that is designed to soak into timber. The difference is covered in Mivan oil vs traditional shuttering oil.
Where Mivan grease goes
Grease goes on the hardware that holds the panels together and has to come apart again at every strip. On a typical aluminium formwork floor that means:
- Pins: a thin film along the full shank, every cycle.
- Wedges: both faces and the slot edge, every cycle.
- Tie rods and wall ties: the threads only, never the sleeve cast into the wall.
- Kicker bolts and prop head threads: the exposed thread, wiped clean first.
- Panel joint edges and corner angles: every few cycles, kept well away from the face sheet.
Formwork systems differ, and some manufacturers ask for certain locks to be kept dry. Where your supplier’s manual names a part to leave ungreased, follow the manual. The full routine is in how to grease Mivan formwork.
What happens when they are swapped
Grease on the panel face
Grease does not spread into a thin film the way a release oil does. Brushed onto a face sheet, it leaves ridges and lumps that press into the concrete surface, collect dust and come off as dark patches on the wall. Greasy patches are harder to plaster and paint, and the crew uses far more product than with oil.
Oil on pins and wedges
A release oil is made to be thin. On a steel pin it runs off within hours, and curing water or rain washes away what is left. Slurry then sets on the bare pin and in the hole, rust starts between floors, and stripping slows down. That is how most sites end up with stuck Mivan pins and wedges.
How much of each a site plans for
Keep oil and grease as separate line items in the budget.
| Planning step | Mivan shuttering oil | Mivan grease |
|---|---|---|
| What drives quantity | Panel face area per pour | Pins, wedges, threads and joints greased per cycle |
| Formula | Face area per pour ÷ coverage × pours, plus 10% | Points per cycle × grams per point × cycles, plus 10% |
| Starting figure | About 30 to 40 m² per litre by fine spray; plan at 30 m² per litre | No standard figure; weigh the tin before and after one shift to find grams per point |
| Biggest waste | Brushing or pouring instead of spraying | Thick coats and greasing pins that still carry slurry |
Planning the oil
Oil use follows panel area. Our Mivan shuttering oil consumption guide uses about 30 to 40 m² per litre for fine-spray application and 30 m² per litre as a safe planning figure. At that rate, a pour with 1,200 m² of panel face needs about 40 litres, plus 10% for touch-ups.
Planning the grease
Grease use follows the number of points greased and how heavy-handed the crew is, so there is no honest single figure per floor. Count the points greased each cycle, weigh a tin before and after one shift to find grams per point, then multiply out. The method, with a worked example, is in Mivan grease consumption.
Is batata grease the same as Mivan grease?
No. Many sites use batata (yellow) grease on shuttering hardware, and KE makes both. Yellow grease and Mivan grease are different grades, and the right one is chosen for the requirement: some jobs need a thicker grease, some a more slippery one. Ask for a sample of either before you order. The trade-offs are covered in batata grease for shuttering.
Ordering oil and grease together
Send your panel area per pour, number of pours, floor-set size and site location. We quote oil and grease as separate lines, any quantity can be supplied, and you can ask for a sample of the grease first.
Frequently asked questions
What is the difference between Mivan grease and Mivan oil?
Mivan shuttering oil is a thin release agent sprayed on the panel face so concrete does not stick. Mivan grease is a thicker lubricant brushed on pins, wedges and threads so the hardware moves freely. Oil goes on the face, grease goes on the hardware.
Can I use Mivan shuttering oil on pins and wedges?
It is not recommended. Release oil is thin, runs off steel within hours and washes off in rain, so slurry and rust build up on the pins and they start to jam.
Can grease be used as a release agent on Mivan panels?
No. Grease does not spread into a thin film. It leaves lumps and patches on the concrete, is harder to plaster over and uses far more product than a release oil.
How much Mivan shuttering oil is needed per square metre?
About 30 to 40 m² per litre by fine spray on clean, dry panels. Use 30 m² per litre as a safe planning figure and add 10% for touch-ups.
How much Mivan grease does a floor use?
There is no standard figure. Count the points greased per cycle, weigh a tin before and after one shift to find grams per point, and multiply by points and cycles, plus 10%.
Is Mivan grease the same as batata grease?
No. They are different grades, chosen for the requirement: some jobs need a thicker grease, some a more slippery one. Ask for a sample of either before you order.
Related: Mivan Shuttering Oil · Mivan Shuttering Grease · Mivan Oil Consumption

