How to Grease Mivan Formwork: Pins, Wedges, Ties and Props

To grease Mivan formwork, clean pins, wedges and threads straight after stripping, let them dry, then brush a thin film of grease on the pin shank, wedge slot, tie rod threads and prop threads. Keep grease off the panel contact face, which takes Mivan oil instead. Grease pins and wedges every cycle.

On an aluminium formwork job, the floor cycle depends on how fast the crew can strip and refix. Most delays at stripping come from hardware that will not move: pins that will not drive out, wedges that jam, tie rods that will not turn. Grease on the right parts, applied the right way, prevents most of this. This guide covers where to grease, how often, and what to avoid. For the product, see our Mivan shuttering grease.

What grease does on Mivan hardware

Grease does three jobs on aluminium formwork hardware:

  1. Lets parts move. Pins drive in and out, wedges lock and release, and threads turn without a hammer.
  2. Stops slurry bonding. A grease film keeps cement slurry from setting hard on the pin or in the thread.
  3. Protects steel from rust. Steel pins, wedges and ties sit wet for days. A grease film slows rusting between floors.

Grease does not go on the panel face that touches concrete. That surface needs a thin release coat of Mivan shuttering oil.

Where to apply grease, and how often

ComponentWhere to greaseHow oftenNote
PinsFull length of the shankEvery assembly cycleThin film, not a blob at the tip
WedgesBoth faces and the slot edgeEvery cycleWipe off excess so it does not drip
Tie rods and wall tiesThreads onlyEvery cycleKeep grease off the sleeve that sits in the concrete
Kicker boltsThreadsEvery cycle
Panel-to-panel jointsEdge holes and contact edges of the frameEvery 3 to 5 cyclesDo not let grease reach the face sheet
Corner anglesJoint edgesEvery 2 to 3 cycles
Prop head screw threadsExposed threadWeeklyWipe dirt off before greasing

Check your formwork manual first. Formwork systems differ. At least one system manufacturer instructs that its assembly locks must never be oiled or waxed. Where your supplier’s manual names a part to keep dry, follow the manual.

Step-by-step greasing routine

  1. Clean straight after stripping. Scrape slurry off pins, wedges and threads while it is still soft. Use a scraper or wire brush on steel parts. Do not hammer the aluminium frame.
  2. Wash and dry. Rinse off loose slurry and let parts dry. Grease does not stick well to wet or dusty steel.
  3. Inspect. Set aside bent pins, cracked wedges and damaged threads. A bent pin jams no matter how much grease it gets.
  4. Apply a thin film. Use a brush or a gloved hand. One light coat along the full length is enough. Excess grease collects dust and gets wiped onto panels.
  5. Grease threads, not sleeves. On tie rods, grease the thread. Keep the part that is cast into the wall clean.
  6. Store greased parts covered. Put pins and wedges in lidded bins or bags between floors so dust and rain do not reach them.
  7. Re-grease before the next fix. If a part has sat out for several days or been rained on, give it a quick top-up.

Give each gang a small lidded tin and a brush. Open pails left on the deck fill with dust and slurry and end up thrown away. Our Mivan grease consumption guide shows how to measure and control how much you use.

What not to use on Mivan hardware

Instead of greaseProblem
Diesel or used engine oilThin, runs off, collects dust that grinds between pin and hole. Can leave marks on concrete
Plywood shuttering oilMade to soak into timber. On steel hardware it runs off and gives little protection
Silicone sprayIf it reaches the concrete face it can leave a film that affects plaster and paint bonding
No grease, “just this once”Slurry sets on the pin, and stripping takes far longer

What to look for in a Mivan grease

A grease for formwork hardware should:

  • Stay put when wet. Curing water and monsoon rain should not wash it off within a cycle.
  • Not run in the sun. Exposed hardware gets hot on sunny days. The grease should stay on the part.
  • Not stain. It should not mark aluminium panels or transfer onto the concrete.
  • Brush on easily. Too stiff and crews scoop thick lumps; too soft and it drips.

Grease for formwork is not one fixed product. Some is thicker, some more slippery, and the right one depends on your hardware and how your crew applies it. KE makes its Mivan grease to the project and requirement. Tell us the application and we will supply the consistency the job needs, and ask for a sample to try on a few pins before you order.

Can batata (yellow) grease be used instead? Many sites use it on shuttering hardware because it is cheap and water-resistant. KE’s yellow grease and Mivan grease are different grades, some thicker and some more slippery, and the right one is chosen per requirement. Tell us your hardware and we will advise, and ask for a sample of either. We cover the trade-offs in batata grease for shuttering.

Season tips for Mumbai and Thane sites

  • Monsoon (June to September): clean and re-grease pins and wedges every cycle without fail. Store greased hardware under cover. Expect to use more grease.
  • Summer: keep grease tins in shade. Hardware lying in direct sun before fixing should be wiped and re-greased if the film has thinned.
  • Between projects: clean, grease and bag all pins and wedges before they go into storage. Rusted pins are the usual cause of a slow first floor on the next job.

Need Mivan grease in bulk?

Tell us your floor-set size, how you apply the grease and your site location, and ask for a sample of our Mivan shuttering grease before you order. Any quantity can be supplied. Rates for larger quantities and delivery cost are quoted with the enquiry.

Krish Enterprises, K.J. Complex, Diva, Thane 400612. Serving Mumbai, Thane, Navi Mumbai and Panvel.

Frequently asked questions

Where is grease applied in Mivan shuttering?

On the hardware: pins, wedges, tie rod and wall tie threads, kicker bolts, panel joint edges and prop threads. Not on the panel face that touches concrete.

How often should Mivan pins and wedges be greased?

Every assembly cycle. Panel joints every 3 to 5 cycles, corner angles every 2 to 3 cycles and prop threads weekly, unless the formwork manual says otherwise.

Should pins be cleaned before greasing?

Yes. Scrape, wash, dry, then grease. Grease over slurry is wiped off at the next strip.

Can I use diesel instead of grease on Mivan pins?

It is not recommended. Diesel is thin, runs off quickly and attracts dust that wears pins and holes.

Can grease go on the Mivan panel face?

No. The contact face takes a thin coat of Mivan shuttering oil as a release agent.

Does every formwork system need its locks greased?

No. Some manufacturers say certain locks must be kept dry. Follow your formwork supplier’s manual.

KY

Krish Yadav

Owner, Krish Enterprises · Mumbai

30+ years supplying construction lubricants to Mumbai's top developers, EPC firms, and infrastructure projects. Specialist in formwork chemistry, hydraulic systems, and industrial greases.

Leave a Comment

Your email address will not be published. Required fields are marked *