Mivan Grease Consumption: How Much Grease per Floor and per Month

Mivan grease consumption depends on how many pins, wedges, tie rods and prop threads you grease each cycle, and how much your crew puts on each. Work it out as: points greased per cycle × grams per point × cycles per month, plus 10% for waste. Weigh the bucket for one shift to find your own grams per point.

Before every new tower, the store keeper or site engineer has to decide how many buckets of grease to order. There is no single answer, because floor sets, crews and greasing habits differ. But the calculation is simple, and once you have measured one shift you can plan the whole job. For the product itself, see our Mivan shuttering grease page.

Why there is no standard figure

Three things change grease use from site to site:

  • Size of the floor set. A larger floor plate means more panels, more pin and wedge joints and more ties.
  • Which parts get greased every cycle. Pins and wedges are greased every cycle. Some parts only every few cycles.
  • Crew habit. A crew that dabs a thin film uses a fraction of what a crew scooping by hand uses.

So rather than trust a rule of thumb, measure your own rate once and scale it.

The formula

Grease per month (kg) = Σ (points greased per cycle × grams per point) ÷ 1,000 × cycles per month × 1.10

The 1.10 adds 10% for spillage, dropped tins and touch-ups.

Step 1: Count the points you grease each cycle

Not every component needs grease every cycle. Typical greasing frequency:

ComponentHow often to greaseCount on your floor set
Pins and wedgesEvery assembly cycle______
Tie rod and wall tie threadsEvery cycle______
Kicker boltsEvery cycle______
Panel-to-panel jointsEvery 3 to 5 cycles______
Corner anglesEvery 2 to 3 cycles______
Prop head screw threadsWeekly______

Your formwork supplier’s drawings or the shuttering contractor’s material list will give you the counts. Always follow your formwork supplier’s manual where it differs from this table. Some systems ask for certain locks to be kept dry.

For points greased every few cycles, divide the count by the interval. Example: 300 corner angles greased every 3 cycles count as 100 per cycle.

Step 2: Measure grams per point (the bucket-weigh method)

This takes one shift and a weighing scale:

  1. Weigh a full bucket or tin before the shift. Write it down.
  2. Ask the gang to note how many pin-wedge sets (or ties, or props) they grease.
  3. Weigh the bucket again at the end of the shift.
  4. Divide the grease used (in grams) by the number of points greased.

Do it separately for pins and wedges, ties and props if you can. Threads usually take more grease per point than a pin.

Step 3: Worked example

Example numbers only. They show the method, not a typical site. Use your own counts and your own measured grams per point.

Suppose the bucket-weigh test gave these results on your site:

ComponentPoints per cycleGrams per point (measured)Grease per cycle
Pin and wedge sets2,0001.5 g3.0 kg
Tie rod threads3003 g0.9 kg
Kicker bolts1502 g0.3 kg
Corner angles (300 every 3 cycles)1002 g0.2 kg
Total per cycle4.4 kg

Prop threads are greased weekly, not per cycle. Say 250 props × 2 g = 0.5 kg per week.

Monthly grease, assuming a 7-day floor cycle (about 4 cycles a month):

  • Per-cycle parts: 4.4 kg × 4 = 17.6 kg
  • Props: 0.5 kg × 4 weeks = 2.0 kg
  • Subtotal: 19.6 kg
  • Add 10%: about 21.6 kg a month

Whole project: a 25-floor tower at this rate needs about 21.6 ÷ 4 = 5.4 kg per floor, so 25 × 5.4 = about 135 kg of grease, plus extra for repeated setups and the podium.

Sizing your order

Match the order to how fast the site uses grease. Open pails on a deck collect dust and slurry. Any quantity can be supplied and there is no minimum order. These are examples of common order sizes, not a list of stocked packs.

Monthly useExample order
Under 5 kg1 kg tins, one per gang
5 to 10 kg5 kg buckets
10 to 25 kgOne 18 kg pail in the store, decanted into 1 kg tins for the deck
Over 25 kg18 kg pails on a monthly schedule

Mivan grease is made to the project and requirement: some grades are thicker, some more slippery. Tell us how you apply it, and ask for a sample before you order.

What pushes grease consumption up

  • Greasing dirty pins. Grease on top of concrete slurry gets wiped off with the slurry at the next strip. Clean first, then grease.
  • Thick coats. A pin needs a thin, even film along the shank, not a lump at one end.
  • Open buckets on the deck. Dust and water get in, crews throw away contaminated grease and open a new tin.
  • Grease on panel faces. The contact face of the panel takes Mivan shuttering oil, not grease. Grease there wastes product and can mark the concrete.
  • Monsoon. Rain washes some grease off exposed parts. Expect higher use from June to September.

How to bring consumption down

  1. Clean pins and wedges straight after stripping, while slurry is still soft.
  2. Give each gang a small lidded tin and a brush, not an open pail and bare hands.
  3. Store greased pins and wedges in covered bins between floors.
  4. Re-run the bucket-weigh test after a month. If grams per point drops, your new routine is working.

The step-by-step greasing routine is in how to grease Mivan formwork.

Oil and grease are separate line items

Budget grease for hardware separately from release oil for panel faces. They are different products with different consumption rates. For the oil calculation, see Mivan shuttering oil consumption.

Need Mivan grease in bulk?

Send us your floor-set size, monthly estimate and how you apply the grease, and ask for a sample of our Mivan shuttering grease before you order. Rates for larger quantities and delivery cost are quoted with the enquiry.

Krish Enterprises, K.J. Complex, Diva, Thane 400612. Serving Mumbai, Thane, Navi Mumbai and Panvel.

Frequently asked questions

How much grease is used in Mivan shuttering per floor?

It depends on your floor set and crew. Count the points greased per cycle, measure grams per point with the bucket-weigh method, and multiply. The worked example above lands at about 5.4 kg per floor, but your figure will differ.

How do I calculate Mivan grease for a whole project?

Grease per floor multiplied by the number of floors, plus about 10% for waste. Add extra for podium levels and repeated setups.

How often should Mivan pins and wedges be greased?

Every assembly cycle. Tie rod threads and kicker bolts every cycle, panel joints every 3 to 5 cycles and prop threads weekly, unless the formwork supplier’s manual says otherwise.

Why is our grease consumption higher than expected?

Usually thick coats, greasing pins that still have slurry on them, open buckets getting contaminated, or grease being put on panel faces instead of oil.

Is Mivan grease the same as Mivan oil?

No. Grease is for hardware such as pins, wedges, ties and props. Mivan oil is a release agent sprayed on panel faces. Budget them separately.

KY

Krish Yadav

Owner, Krish Enterprises · Mumbai

30+ years supplying construction lubricants to Mumbai's top developers, EPC firms, and infrastructure projects. Specialist in formwork chemistry, hydraulic systems, and industrial greases.

Leave a Comment

Your email address will not be published. Required fields are marked *